PERMAKOTE® SUPER PLUS

PERMAKOTE® SUPER PLUS Rubber Roof Sealant innovative Resin Technology combines a superior blend of elastomeric acrylic resin and a single component polyurea to form a super strength high durability ponding water coating and ponding water area topping. Use as either: 1- a complete three coat system which includes a primer coat of PERMABOND™ Bonding Primer or METAL-PRIME RED-OX™ Rusted Metal Primer Sealer and two coats of PERMAKOTE® SUPER PLUS roof coating or 2- as the third and final coat over one coat of primer and one coat of PERMAKOTE PLUS® Flat Roof Coating, or 3- as a ponding water area topping over the completed PERMAKOTE PLUS® flat roof coating system -see Warranty Information Below-.

For a High Solids Silicone Elastomeric Roof Coating check out our Best Silicone Roof Coating .

Use as either: 1- a complete three coat system which includes a primer coat of PERMABOND™ Bonding Primer or METAL-PRIME RED-OX™ and two coats of PERMAKOTE SUPER PLUS® or 2- as the third and final coat over one coat of primer and one coat of PERMAKOTE PLUS®, or 3- as a ponding water area topping over the completed PERMAKOTE PLUS® System (see Warranty Information Below).
Recommended for well-draining, FLAT or SLOPED roofing surfaces (see Warranty Compliance Information Section Below). Excellent adhesion on weathered wood, shakes, plywood, clapboard, primed metal, galvanized, aluminum, tin, copper, asbestos, asphalt, urethane, polyester, primed styrofoam, fiberglass, built-up-roofs, bonded roof gravel, rolled roofing, modified bitumen membranes, mineral surfaced roofing, concrete tiles, clay tiles, masonry tiles (flat or barrel), primed synthetic or aluminum, adobe, slate, slab, properly prepared EPDM, and various other substrates.
PERMAKOTE SUPER PLUS® is ideal for residential, commercial and industrial applications.

SURFACE PREPARATION:
Apply only to a sound, completely dry, well prepared roof surface. Leaks must be repaired before any coating is applied. If primer was applied, it is essential that the primer surface is clean and dry and free of all moisture. If no primer was applied, prepare surface by thoroughly pressure washing with a water and chlorine mixture using at least 1500 P.S.I. to remove any previous coatings, dirt, grease, and other foreign materials, especially mold, mildew and algae. PERMAKOTE SUPER PLUS® will resist mildew growth but will not kill mildew already on the surface. Patch any holes, cracks, flashings, valleys, vents, etc., with PERMAPATCH™ Elastomeric Patching Compound, a Waterproofing Caulk and Sealant. Tape & seal all seams with PERMATAPE™, a Polyester Fabric Tape or PERMASTIK™ Butyl Tape.

Metal:
Clean surface of all grease, oil and foreign matter before priming. Rusted metal and uncoated metal must be primed with METAL-PRIME RED-OX™, a Red Iron Oxide Primer Sealer. Use a degreaser on galvanized or coated metals which have oils or surface treatments. Check PERMAKOTE SUPER PLUS® adhesion on galvanized or coated metal by applying to a small area and evaluating after 48 hours. If lack of adhesion is present after evaluating, metal must be lightly scuffed without penetrating the coated finish or galvanizing. If applicable, use METAL-PRIME RED-OX™ to spot prime the penetrated areas, then use PERMABOND™ Primer for entire coated or galvanized surface.

APPLICATION PROCEDURE:
Stir well before using. Do not thin, use product as is. Mix multiple containers of color together for greater color consistency. Do not apply when temperatures are below 45 degrees Fahrenheit or when humidity is very high. Do not apply when coating will be subjected to rain or heavy dew before it has had enough time to dry (approx. 2 to 4 hours). Drying time will vary depending on temperature, humidity and location. Apply using brush, roller or spray. Spread coating uniformly. Spread Rate will vary depending on surface. Apply each coat between 12 to 16 mils wet film thickness. Wait at least 12 hours before applying a second coat. Two coats resulting in a minimum 16 mil total dry film thickness is recommended. If primer was used, a minimum 20 mil total dry film thickness is required and is mandatory for warranty compliance.

Airless Sprayers:
Use at least a 1 gallon per minute piston type airless sprayer with a minimum tip size of .027. Remove line filters and gun filters before spraying.

Clean Up:
Clean up all spills, tools and overspray immediately while the coating is still wet with warm soapy water.